mac address learning is not supported in rspan

MAC ADDRESS LEARNING IS NOT SUPPORTED IN RSPAN MAC

removing single points of failure with multiple Layer 2 switches.link-state dynamic routing that provides redundant routes.redundant links between Layer 2 switches.implementing VLANs to contain broadcasts.Which two network design features require Spanning Tree Protocol (STP) to ensure correct network operation? (Choose two.).

MAC ADDRESS LEARNING IS NOT SUPPORTED IN RSPAN MAC

In order to forward packets, Cisco Express Forwarding (CEF) requires the MAC address of the next hop provided by ARP.

Which protocol is required for Cisco Express Forwarding to be able to successfully forward packets on a multilayer switch?.

address resolution protocol (ARP) memoryĬAM is used by ARP to store MAC and IPv4 address pairs.

ternary content addressable memory (TCAM).

What type of specialized memory is used to facilitate high performance switching in Cisco multilayer switches?.

InterVLAN routing using subinterfaces is not a CEF technology, and route processors using stateful switchover is a redundancy technology used by routers. Cisco software-based routers use the general-purpose CPU for packet switching.

route processors using stateful switchoverĬEF switching on Cisco hardware-based routers uses forwarding engines implemented in specialized ASICs to forward packets.

forwarding engines implemented in specialized ASICs.

Which technology does CEF switching use on Cisco hardware-based routers to forward packets?.

The native VLAN must be configured the same at both ends of the trunk link.

The native VLAN interface configurations must match at both ends of the link or frames could be dropped.Ĩ02.1Q is a standard trunking protocol where untagged frames are placed on the native VLAN.

Private VLAN configurations are not supported.

It is a proprietary protocol that is supported on Cisco switches only.

Untagged frames will be placed in the configured native VLAN of a port.

Which two statements are true about the 802.1Q trunking protocol? (Choose two.).

VLANs are associated with switch Layer 2 access and trunk ports.

The interface vlan global configuration command is used to create a routed port.Ī switch routed port is a Layer 3 port that requires removal of Layer 2 port functionality with the no switchport interface configuration command.

To create a routed port requires removal of Layer 2 port functionality with the no switchport interface configuration command.

A routed port is not associated with a particular VLAN.

A routed port is a physical switch port with Layer 2 capability.

A routed port behaves like a regular router interface and supports VLAN subinterfaces.

Which two statements are true about routed ports on a multilayer switch? (Choose two.).

Switches that perform Layer 3 switching process packets at Layer 2 hardware speeds while providing the scalability of routing.

to implement the routing process by using routed protocols.

to provide a better path to the Internet without using routing protocols.

to integrate all of the networking functions into one device.

to process packets at Layer 2 switching speeds while utilizing the scalability of routing.

Only ports which have a device connected and active will show the mac address detail.CCNP ENCOR Packet Tracer Activity Files Answersġ.2.1 Packet Tracer – Inter-VLAN Routing Challenge AnswersĢ.2.1 Packet Tracer – Observe STP Toplology Changes Answersĥ.2.1 Packet Tracer – Configure VTP and DTP Answersĥ.2.2 Packet Tracer – Configure EtherChannel AnswersĬCNP ENCOR Student Lab Source Files Answersġ.1.2 Lab – Implement Inter-VLAN Routing AnswersĢ.1.2 Lab – Observe STP Topology Changes and Implement RSTP Answersģ.1.2 Lab – Implement Advanced STP Modifications and Mechanisms Answersĥ.1.3 Lab – Implement EtherChannel Answers With the above command, one can figure out which Mac address is on which port of catalyst switch. Switch# show mac-address-table | include 0009.aabb.06e9 Or if you know the mac address and want to know which port the mac address is coming from, use the following command

Switch# show mac-address-table | include Fa0/5 If you know the switch port you can use the following command Only ports which have the device connected and active will show the mac address detail. mac address of the connected device) and port number. The mac address or CAM table shows the Vlan associated with the port, MAC being learned on the port (i.e. With the command, you can figure out which MAC address is on which port. Total Mac Addresses for this criterion: 5

Mac address learning is not supported in rspan